How to set up wifi router huawei ws329

The Huawei WS329 wireless WiFi router is an entry-level model in a line of three budget broadband access devices (WS319, WS329 and WS330) from the famous Chinese manufacturer of networking and telecommunications equipment, which is increasingly moving into the mass SOHO segment of the market. At the time of writing, the price of the device is about 1,300 rubles. It is slightly more productive than the WS319 due to the Ralink RT63365E chip used, which, although not much, is faster. This chip is purely budget with a low clock frequency. As an example of use, I can cite the Upvel UR354AN4G universal router. There is no additional cooling system on the chip - even radiators are not glued to the case. A significant disadvantage of such a technical solution is the fact that third-party software developers do not like this chip, which means there will be no alternative firmware.

Otherwise, the characteristics of the device are not particularly remarkable and are almost identical for all three models in the line:

— FastEthernet 10/100 Mbit/s network switch: 1xWAN and 4xLAN — Wi-Fi module 802.11n, 2.4 GHz, maximum theoretical speed up to 300 Mbit/s — 2 non-removable antennas with a coefficient of 5dBi

The packaging is typical for an inexpensive device and is more than sufficient for it - a LAN cable, a power supply and a mini-instruction manual.

At the time of writing, the current firmware version is V100R001C199B011. She is English speaking. There is full support for IPTV digital television, including using VLAN 802.1Q. Of the obvious problems, the only obvious problem can be identified is the unstable operation of VPN over the L2TP protocol. No other significant problems were identified.

Setting up the Internet depending on the type of connection

It's important to think beyond the configuration of your wireless network.
Without access to the Internet, it will not make sense. That is why, in the “Internet” or “WAN” tab, a connection to the provider is created, taking into account the data specified in the contract with him. It also depends on the type of connection.

PPPoE protocol

If the Internet is provided via PPPoE, then you will need a login and password, which are issued by the provider when concluding the contract. The steps are as follows:

Select PPPoE type;
Enter your login and password;
Disable the secondary connection option;
ABOUT.

Connection via dynamic IP

To establish this type of connection, you do not need to enter your provider login and password. It is enough to do the following:

Mark the lines to enable connection and Internet;
Define type as IP;
Select NAPT connection type;
Addressing type - DHCP.

L2TP or PPTP connection

L2TP is practically no different from the previous type, except that you will additionally need to specify the name of the operator’s server. Instructions:

Select L2TP type;
Enter your login and password;
Check the box next to “Dynamic IP”;
Enter the server address;
Set the MTU size to 1460, which will be optimal.

But PPTP can be both dynamic and static. Often providers provide communications in this protocol, so you need to be able to configure it. To do this, you need to know the login information for the server and the address of the server itself. If everything is known, then you can start configuring the PPTP dynamic option:

Select the appropriate type;
Enter your username and password to log in;
Activate dynamic IP and enter the server address;
The MTU value is set to the optimal value of 1420;
The automatic connection function is activated.

Important! If a static IP was obtained using the same protocol, then the parameters will be slightly different and will include: login information, your IP, server IP and subnet mask, gateway, and DNS server address. It is important to change the IP from dynamic to static at the configuration stage

Setting up the PPPoE protocol

To configure the PPPoE
you need to do the following:

go to the main device settings menu;
select “Internet Settings”;
in the window that appears, check the boxes “Enable connection”, “Service type - Internet”;
select “IP routing PPP” from the list of connection types.
Leave the rest of the values as standard.

After you have set all the settings according to the specified instructions, all you have to do is enter the values in the “login” and “password” fields, which were provided by the operator when drawing up the agreement. In the remaining PPP Service Name field, enter the value “internet.”

Working with the terminal

How to set up and flash a Huawei hg8245h router
This method also requires root, as it works directly with the Linux kernel in Android OS. You need to install the Terminal Emulator program. We connect the smartphone with a cable and enable modem mode in the phone settings. Then you need to enable network sharing (as is the case with Reverse Tethering). In the terminal emulator you need to enter the command:

In the window that appears, you need to find and write down the IP address of the USB0 connection. Then, in the network connection of the smartphone on the PC, you need to open the properties of this connection, select “Protocol” and click “Properties” at the bottom right. Instead of automatically obtaining an IP, you need to check the “Use the following IP” checkbox. In the IP line, you must enter the address corresponding to USB0 on the smartphone, but replace the last number with one.

In the terminal on your smartphone you need to enter the following commands:

ifconfig usb0 up

route add default gw dev usb0 (where

– IP address previously set on the computer.

setprop net.dns1 8.8.8.8

(You can use another DNS server)

Internet is connected. You can automate the action by writing a script (for example, in the GScript program) with the commands:

ifconfig rmnet0 down

ifconfig usb0 up

route add default gw "your IP address" dev usb0 setprop net.dns1 " DNS server address"

How to access 192.168.8.1

How to set up a tenda router yourself and connect wifi

Review and configuration of the D-Link Dir-320 modem

Instructions on how to enter the settings of a Huawei router include steps from physically connecting two gadgets to changing the standard conditions in 192.168.8.1 admin: password, login, Wi-Fi, network name.

Step 1. Connect to a desktop computer, laptop or phone

In a Huawei modem, the 4G setting depends on the equipment selected as the “base”: PC, laptop or smartphone, each of them has its own circuit.

For a computer or laptop you need:

connect the LAN wire to the input connector of the Huawei modem;
connect a computer or laptop with a LAN cable to the router;
or insert the modem directly into the USB port.

Connection via phone or tablet is carried out via Wi-Fi, for this you need:

Make sure that mobile Wi-Fi is turned on in the “Settings” menu, or open the curtain and click on the corresponding icon.
Find the one you need in the list of networks and log in.
Most models will not require a password, but if the device asks for one, the information is listed on the back of the modem.
After logging into the Huawei network, access to the router through admin. The panel will open.

Step 2. Connect to your personal account at 192.168.8.1

Open a browser: Safari, Internet Explore, Opera or any other.

Error when logging into the web interface

A common mistake that occurs when entering this address is the writing of characters. Letters may be printed instead of numbers, there may be an extra space or an erroneous number. Enter admin as username and password. This is the factory password; you can change it later. To avoid hacking and after resetting the settings with the Reset button for some reason, you will need to come up with a new password. The number of characters must be no shorter than six, and the use of Latin letters is mandatory.

Step 3. Authorization in the router’s personal account

The appearance of the personal account page depends on the type, model or mobile operator. However, most routers have a single shell, including using mobile WiFi, logging into the system is carried out like on a PC. The WiFi modem has an additional security function with the obligatory entry of a login and password when trying to enter any point.

Step 4: Change Settings

After logging into the Huawei router, the type of connection is configured in more detail depending on the state of the IP address, dynamic or static.

For WAN the procedure is as follows:

Check the “WAN connection” box.
Enter the VPI/VCI values that are assigned to the service in the region by the provider. As a rule, for the Internet VPI is 0, for cable television - 2. Information is indicated in the contract or on the official website or forum.
Specify the connection type as “PPPoE”.
Enter your login and password.
Click the Submit button to save the profile.

Dynamic IP on some types of modems is configured in the same way and differs in only three variables:

In the Connection type line, select IPoE.
Select “DHCP” from the list in the Address Type line.
Activate NAT, if given a choice, then register NAPT.

The next step is setting up a WiFi network through the WLAN tab:

Select the first Network with index “1”. She will be the main network

Additional Information! The router has several WiFi profiles available. The number depends on the firmware, and the last ones on the list of networks will be considered guest.

Fill in the SSID field with the name of the new network. The name is then displayed on all devices.
Check the "WMM" box.
The value “40 MHz” is placed in the Width line (channel frequency).
Security type select WPA2-PSK with AES encryption.
A mandatory condition is to enter the network access password in the “WPA pre-shared key” line to prevent unauthorized access.

Method 1: Remote Control Feature

Almost all firmware of any router has a “Remote Control” function, which is disabled by default. It is open for configuration and allows you to establish access for all targets or only a specific computer for remote control, and such configuration is performed as follows:

After authorization in the Internet center, open the “Protection” section and find “Remote control” there. The menu location may vary depending on the type of web interface. Sometimes, for example, you need to open the “System” menu and find the required item there.

If you want to make sure that any computer can connect to the router, enter the IP address 255.255.255.255. When granting access only to a specific target, enter its IP address in the line. However, keep in mind that it must be static, because if changed, the parameters will be reset. When finished, be sure to save your changes. Change the value back to 0.0.0.0 in the event that remote access needs to be terminated.

When opening access to all devices, you should take care of protecting the web interface to prevent the router from being hacked. To do this, open the “System Tools” section and go to “Password”.

We advise you to change not only the password, but also the username for logging into the Internet center. If you are not sure that you will remember the data, write it down or save it in a text file, because the default values can only be restored by completely resetting the router.

Now, when you enter the router’s IP address in a browser on a remote computer, you will be taken to the web interface with access to managing settings.

Additionally, we note that when selecting a specific target for providing remote control, you will need to specify its exact IP address. To determine it, you can use the router’s web interface as shown above, or the instructions in other articles on our website.

Login to settings, settings IP address, default login and password

How to reboot a wifi router

In order to enter the system menu of the Huawei HG8245 router, you must perform the following steps:

Launch any web browser.
In the address bar field, enter the IP address https://192.168.100.1 and click on the “Go” icon.
On the start page of the system menu of the Huawei HG8245 router that opens, fill in the Account fields, where you enter your login and Password, where you enter your password.
By default, the Huawei HG8245 router uses the root login and admin password.
After entering your username and password, click on the Login button.
In some versions of router firmware, the Rostelecom provider sets the login telecomadmin and password admintelecom.

After completing the above steps, the main window of the router system settings will open.

In the main window, carry out the initial settings of the router

Changing the password to enter settings

Since the factory password for entering the system menu is the same for all routers of this type, this affects the security of the Internet connection. Knowing the password, you can monitor the user’s work on the network, have access to confidential information and block access to the Internet.

In the system menu it is possible to change the factory password to your own. This must be done if the router is not connected to the Rostelecom provider network. With the latter, access to the system menu is controlled by technical support, so there is no need to change the password.

To change the password you must do the following:

After entering the system menu, go to the System Tools section.
On the left side of the window, click on the Modify Login Password tab.
Enter the old password in the Old Password field.
Enter a new password in the New Password field.
Reenter the new password in the Confirm Password field.
Confirm the password change by clicking the Apply button.

For a higher level of security, the password must contain from 9 to 30 characters, including Latin letters and numbers.

We configure the Internet itself depending on the type of connection of your provider

The first setup step is the most important: you need to correctly specify the protocol - the one your operator uses. Otherwise, you will not connect to the Internet. Therefore, we take the contract or memo that the specialist left after installing the cable, and read it carefully. There you will find all the connection information, including the protocol and network login information.

Even if you don’t find anything in the contract in the end, don’t panic. Call the operator's technical support - they will explain everything to you and help you set up the Internet. We will look at setting up the three protocols below. Select the instructions you need and follow them.

PPPoE protocol

Such large operators as Dom.ru, Rostelecom, TTK, NetByNet and others work with this high-speed connection. How the protocol is configured on Huawei:

Go to the second section “Internet” - you will go straight to the first tab with its settings. That's what we need.
In the “Basic Information” block, check the box next to the item about enabling the connection.
Set INTERNET as a service. In the panel with a list of protocol types, select “PPP Routing”.
In IP mode, specify a dynamic value. If you bought a unique address on the Internet from your operator, set it to “Static” and enter all the data from the contract.
The next thing to change is the trigger mode. Set it to "Always online".
Fill in the “Internet account” and “Internet password” fields with the data that is in your agreement with the provider. After that, save the changes using the button below.

Connection via dynamic IP

Unlike the previous type of connection, dynamic IP does not require you to write authorization data. You only need to do the following:

Open the Internet settings tab. Activate the connection and select IP rooting (IP) in the protocol drop-down menu.
Leave the NAT type as default.
In the IPv4 menu, set DHCP. Click on “Save”.

L2TP or PPTP connection

For example, Beeline has a network with the L2TP protocol. Both types are configured in the same way on a Huawei router:

Follow the steps above to set the connection type to "Dynamic IP".
Now in the same “Internet” section, open the VPN tab. Select one of two menus - L2TP or PPTP (depending on what your provider uses).
Check the box next to “Enable” to activate the protocol.
In the WAN connection, specify the previously created connection with a dynamic IP.
In the LNS address field, enter the address of your operator's VPN server.
For PPP username and PPP password, enter the information from your ISP agreement.

How to connect to a Huawei E8372 3G-4G modem via the 192.168.8.1 web interface via wifi?

In theory, if you bought a Huawei E8372h modem from one of the operators, the Internet should work immediately. But if you purchased it separately and inserted the SIM card yourself, then you may actually need to get into his personal account.

In addition to the classic method via USB, there is another option to connect to a Huawei modem via WiFi for detailed configuration. The fact is that the Huawei E8372h, unlike the E3372h, is also a router, that is, it can distribute a wireless signal to any other computers, laptops and smartphones.

If you use this modem to relay 3G-4G Internet via WiFi as a router, then to connect to it there is no need to insert the device into the USB port of the computer. You can use any extension cord or external battery.

The network name and password for connecting to its default signal are indicated on a sticker under the modem cover. Most often, IP addresses 192.168.8.1 or 192.168.3.1 are used to log into your Huawei personal account via the web interface. For example, this is what the information looks like on the Huawei E8372H label

If you purchased a modem from a cellular operator, then the web interface page of your personal account may look like “status.megafon.ru” or “home.beeline”. To log in, you need to log in - the default login or password is “admin/admin” or in some modifications “admin-password”.

They will immediately offer us to change them immediately for greater safety.

And after the replacement we get to the main page of the control panel. Here you can already make detailed modem settings.

How to enter the settings of a router from the manufacturer Huawei.

In order to connect a Huawei router,

Let's perform the following step-by-step actions. With the back of the router facing you, you need to:

Connect the Internet cable coming into the apartment to the blue socket of the router, called WAN;
Next, you need to connect the wire from the computer to the router into any of the four sockets, they are named LAN1, LAN2, LAN3, LAN4. Can be used both for a computer and for a TV and other equipment that can be connected;
In the Power connector, you need to insert the power cord and plug the device into the outlet;
We also see here the WPS or Reset key, which helps if you have forgotten or don’t want to enter the password, but you need to be near the router, or you need to reboot it. All you need to do is press this key;

We are done with the router connectors and its connection to the computer and network.

Let's go to the settings:

Go to the browser and enter the code: “192.168.1.1” - this is the provider firmware;

Since the computer is connected via a wired connection, in the window that opens, in the fields that appear (user name and password), enter, for example, the same word “Kievstar”

Next, a menu appears with three blocks:

— WI FI setup;

— checking the network status;

You can immediately use the setup wizard by clicking on this block. Your next steps will be described step by step in the setup instructions on the screen. You can press the automatic connection button or the manual mode button;

We will start with the wi-fi settings block, since the default is DHSP, which is used in our network;

A window opens where the SSID is written - this is the name of the network and its password, which consists of at least 8 characters and can be viewed by checking the required box. There are also buttons to enable, disable the network and save, which we need to click on to save our data.

Next is the Internet tab, where we can see all the addresses, DNS service, and so on, and you can set up parental controls right there.

7.1. Network security (we do not recommend setting it to a high level; low or medium is enough), because in addition to this, there is also a security system on the computer itself.

7.2.View all devices that have ever been connected.

7.3.View the interface, where it will be written which input (LAN..) is occupied, mac-address, ip-address and their settings.

7.4. Wi-Fi settings, where you can configure everything at your own discretion, turn the wireless network on and off, change its name and some other functions. Here you can put the hide network icon, then no one will see it and to connect to it you will need to enter not only the password, but also the name that you specified.

7.5. It is better not to change anything in the additional settings, since everything is set to “auto” mode and connects independently, adapting to your Internet provider.

7.6. Access to the wi-fi network, here you can put an icon on the VPN connection by pressing a button. This means that you do not need to enter a password to log into the network; you just need to press the button on the back of the router, as mentioned earlier. Allow all devices to connect to the router.

7.7. Guest networks, you can configure a guest network that will not have security or will have it, but minimally;

Maintenance tab. All settings that were specified by you or automatically by the network are shown here. For example, you can quickly and easily see which input (LAN..) your computer is working on and what other devices are connected to this router and which input. Information about network activity is shown, how much is entering and leaving the router.

You can also check the network status. By clicking on the “check network status” section, a window appears showing which devices or appliances are connected to the wireless network. In this case, we see that two devices are connected to this wireless network. Laptop and Android. The Earth icon indicates the Internet gateway, the next one is the router, when you click on it you can get complete information about: IP address, mac address, device ID, AO version, software version.

There is a sticker on the bottom of the router. It indicates all the data on the router, name, modification, energy consumption, country of origin, and so on. Share link:

Source

Huawei WS329 wireless router

Huawei today is widely known as a manufacturer of smartphones, tablets and cellular modems. Having unique experience in the development and production of large solutions in the telecommunications field, the manufacturer recently decided to bring home wireless routers to the open market.

One of the first models was the budget Huawei WS329 with wired ports of 100 Mbit/s and 802.11n in the 2.4 GHz band with connection speeds of up to 300 Mbit/s.

Delivery set and appearance

A sample was provided for testing, so we do not have exact information about the package. Judging by the product descriptions in online stores, in the box the user will find a router, a 12 V 0.5 A power supply, one network cable, brief documentation and CDs.

In appearance, the WS329 differs little from other devices in this segment. It has a black plastic case with dimensions of about 18x12x3 cm excluding connectors and antennas. The top cover has a glossy finish. The manufacturer’s logo is placed in the center, and eight blue LED indicators are installed along the bottom edge: power, Internet, WLAN, WPS, LAN1-LAN4.

The bottom of the case and the antenna are matte. For installation, four legs are used that do not have rubber inserts, or two holes for placing antennas on the wall with the antennas down or up. Passive ventilation slots are located at the bottom and at the ends of the top cover.

On the rear panel you can see two non-removable antennas, a power supply input and a switch, a button, five network ports without indicators. A single button can be used to initiate WPS pairing, to disable WLAN, and to perform a hard reset.

Apart from the impractical gloss on the top panel, the device has a good design, which, however, does not stand out as anything unusual. Another small quibble is the small “cloak” over the connectors on the back, which makes it difficult to unplug network cables by blocking the latch on the plug.

Hardware configuration

The printed circuit board occupies only part of the housing. The router is based on the Ralink RT63365E processor. The volume of the RAM module is 32 MB, 4 MB flash is installed for the firmware.

A network switch (all ports are 10/100 Mbit/s) is built into the processor, and to implement Wi-Fi, an external Ralink RT5392L chip (802.11n, 2.4 GHz, 2T2R, up to 300 Mbit/s) was added. The antenna cables are soldered to the board, but there are also micro connectors.

Note that there are no radiators on the chips, but they are located on the bottom side of the board. However, during testing we did not notice any problems with overheating. On the board you can see a group of pads for a console connection, but access is blocked by an unknown password.

Testing was carried out with firmware version V100R001C199B011 provided by the manufacturer.

Settings and features

Considering the positioning of the model in the budget segment, it is unlikely that we will encounter any functions that go beyond the standard scope here. The web interface is available at 192.168.3.1. In the firmware version under review, it is only in English. Access to it can be limited by client IP addresses. To configure the device via the Internet, the HTTPS protocol is used.

There is built-in help for some pages. Without entering a password, information about the status of the device is available - hardware platform and firmware versions, Internet connection, wireless network name and some other data. It’s convenient that the link “forgot your password?” shows how to reset the settings.

On the main page there are three large icons that allow you to launch the Internet connection setup wizard, change basic Wi-Fi options and view the current network connection diagram. In the scheme, you can quickly set restrictions for clients - on download speed and on the time of access to the Internet.

For more detailed system settings, three menu sections are provided: Internet, home network and maintenance.

The WAN port supports bridge mode, IPoE, PPPoE, PPTP and L2TP. Note that the last two options are configured on a separate page, and not through a single list of capabilities.

To support IPTV, you can use the allocation of wired ports to bridge mode with WAN, a separate IPoE or PPPoE connection, VLAN technology and multicast (IGMP snooping, IGMP proxy). The user can add his own entries to the routing table and also use RIP.

The device supports ALG for some protocols: PPTP, H.323, RTSP and SIP.

The router can limit the Internet access time for clients. In each rule, you can specify the time by day of the week and the MAC addresses of the systems. There is also a URL filter by keywords. It does not support scheduling, but can only be used for selected clients. For the schedule to work, there is support for a built-in clock with synchronization via the Internet.

Implementation of remote access to local systems is carried out using DMZ and port translation rules. They can use port ranges and have different external and internal numbers. Port switching technology has also been implemented

In addition to the usual firewall with protection against several types of attacks, the router provides programming of rules that block access of specified clients to specified Internet services (the latter are indicated by the port number of the remote system).

The manufacturer has provided a bandwidth management function. After specifying the characteristics of your Internet channel, you can create rules with restrictions on download and upload speeds based on IP, MAC, physical port or application.

Given the router's relatively fast processor, this service may be interesting in some configurations. However, we note that its use can lead to a decrease in the maximum speed performance of the router in routing tasks.

A separate page provides information about all connected clients on the local network segment. You can also view the connection status of wired ports.

By default, internal addresses are issued to clients by the DHCP server from the network 192.168.3.*, while the router address is 192.168.3.1. These parameters can be changed if necessary. It is possible to specify MAC-IP pairs to assign permanent addresses to clients.

Basic settings for a wireless access point include the network name and security mode (open network, WEP, WPA/WPA2-PSK).

Additionally, you can select the transmitter power, enable client isolation, set the network type (b, g, b/g, b/g/n), channel number and width, and guard interval.

Note that in our copy there was a “region” item, but it was set to read-only mode (Great Britain was selected).

To simplify client connection, WPS technology is supported, both with a button and with a PIN code. You can restrict client access to Wi-Fi using a white or black list of MAC addresses. Let us mention the presence of WDS mode.

In addition to the main network, you can also organize a guest network, which has a different name and protection mode. Its clients will not be able to access the LAN segment and will only work with the Internet (they are even given addresses from a different subnet).

The factory settings of the wireless network already use protected mode with an individual password. The network name and router key are indicated on the sticker.

The last section contains familiar items for changing the administrator password, updating firmware, working with configuration, rebooting, as well as system information and an event log (not very detailed, but with the ability to send to the syslog server). The device keeps statistics of data reception and transmission across interfaces (LAN1..LAN4, Wi-Fi, guest network). There is an option for “one-button” diagnostics of the router, as well as ping and traceroute utilities.

Performance

We were unable to test the device with Beeline Internet - the L2TP connection was apparently established, but access to the Internet did not work. The lack of detailed logs and diagnostic tools made it impossible to understand the situation.

So only synthetic tests were used to test performance. Since the router only has 100 Mbit/s ports, we tested it on the version of the stand used in most previous materials.

All options for connecting to the Internet were checked.

When using IPoE, PPPoE and PPTP modes, the user can count on almost full channel speed of 100 Mbit/s. Higher load in the L2TP client reduces the maximum speed to 60-70 Mbit/s. In addition, it should be noted that the latter option turned out to be not very stable in tests - prolonged operation under high load led to loss of connection.

The router is capable of providing access to the provider’s local network simultaneously with VPN connections to the Internet. There are no comments regarding the speed of operation in this mode; the indicators are shown in the following graph.

When loaded by a p2p client, the router in all modes except L2TP showed a real operating speed of 8.5 MB/s, while the number of connections was 500 or more (no restrictions were set in the client). With L2TP, work in this scenario was unstable, which once again confirms the poor implementation of this function in the firmware version under review.

The router has a wireless module with a maximum connection speed of 300 Mbit/s. However, in practice, in the presence of neighboring networks, it cannot use a wide channel, so you can only count on 144.4 Mbit/s. However, given the use of 100 Mbit/s wired ports, this should not be considered a significant limitation on the Internet access speed of wireless devices.

Wi-Fi speed testing was carried out with a TP-Link TL-WDN4800 adapter. The distance between the devices was about 4 meters. The router was configured to operate in the 802.11n standard with a 20/40 MHz band and WPA2-PSK AES protection. The numbers represent the speed of operation of a wireless client with a PC in the LAN segment and with a server on the Internet for various connection options.

The results of the wireless controller performance test can be considered good for the hardware configuration used. In all modes except L2TP, the client can count on 85-95 Mbit/s when working over Wi-Fi.

In general, the device performed quite well for the segment and hardware configuration under consideration. Apart from L2TP, the implementation of which clearly requires improvement, the router can be effectively used with connections with speeds up to 100 Mbit/s inclusive.

conclusions

The Huawei WS329 wireless router is a typical representative of the modern mass segment of home devices. Its technical characteristics, hardware and software platforms are well balanced, which suggests the absence of redundant functions and speed restrictions in the main use cases.

The use of a sufficiently fast processor provides routing speeds sufficient to service channels up to 100 Mbit/s. There are also no comments regarding the operation of the wireless module.

The current version of the firmware does not cope well with working in L2TP mode, which is found in domestic operators. We were also unable to test the functioning of IPTV multicast broadcasts.

I would like to hope that the company has enough resources to correct the detected deficiencies.

It is difficult to expect a wide range of functions from products in this price category, so we will only note support for scheduling Internet access for individual clients and a guest wireless network.

It will not be easy for the company to find its niche, since with a price of about 1,000 rubles, there are devices on the market with similar characteristics from more well-known manufacturers.

The device is already available on the local market. Cost information is provided below.

Source: https://www.ixbt.com/comm/huawei-ws329.shtml

What to do if you forgot your Wifi password?

This is not a rare case because we see that many people have difficulty remembering their password. It's even easier to forget your Wi-Fi password since we have Wi-Fi everywhere. School, home, restaurants, cafes, gyms, or even the garage often have different Wi-Fi networks.

You need to reset all settings to factory settings. Each router or modem has a button that helps you erase all previous settings. After rebooting, the modem will become completely new.

Now the settings will return to the default modem username and password and all you have to do is configure everything again.

How to set up Wi-Fi on Huawei using a computer?

We provide you with another method to set up your 3G/4G Wifi modem. To do this, you need to use a laptop or a regular desktop PC.

Step 1: Connect to Wi-Fi

Same thing with using a phone, you need to connect your laptop to Wi-Fi by default. The default username and password are located on the back of the router. They must include the SSID and key (password) to enter the Wi-Fi setup.

Step 2: Login to IP 192.168.8.1

On a laptop, you cannot configure the application, but you can log in with the default IP address 192.168.8.1. Any internet browser from Firefox or Chrome can access this site, so simply enter this IP in the address bar (as if you were visiting a site) and press Enter.

192.168.ll - login to the admin panel

The site will require you to select a language and then a username and password before logging in. This site by default requires admin/admin details according to ID and password. Now we move on to the main task. It's set up.

Step 3: Set up your Wi-Fi

Find the path to the configuration function. Next, we need you to select a WLAN to create basic settings for that network. You are allowed to change all information as follows Select a name for the new Wi-Fi and enter it in the SSID field

In the WPA Pre-Shared Key, you must create a password for the newly created Wi-Fi name. The requirements are the same as on a mobile phone. Finally, don't forget to click the Apply button to save your settings. Without saving, your settings will be deleted when you log out.

Main sections

Let's go over each section of the existing firmware. Let's start with the main one:

As you understand, the main purpose of this section is to show general information. Connection type (4G), operator (Megafon), signal level, transmitted traffic, Wi-Fi clients, access to flash drive files (perversion). As a convenience, I have marked with an arrow the disabling of mobile data transmission - if you need to save money, you can safely turn it off periodically.

Go to the “Statistics” page. Here awaits us... statistics

Transmitted data (pay attention to the “mileage” of my modem - especially for you from the factory), connected clients and black list (to be further)

On the “SMS” tab, you can read incoming messages (remember that when they arrive, the light comes on) or send them. Unfortunately, there are no USSD requests in the stock firmware (for example, to view the balance), but this is available in alternative firmwares.

On the “Update” tab, you can check for the latest official firmware and, if necessary, download them.

Attention! If you still want to switch to alternative firmware, I recommend putting this section aside, because... periodically new versions do not allow third-party firmware to be installed on them and we have to wait for our geniuses until they come up with a new way

Setting up a WiFi network on the Huawei E8372H-153 modem

Unlike the E3372, the Huawei E8372h-153 modem has a separate block of configurations related to setting up a wireless network for distributing the Internet via wifi to other computers, laptops or smartphones.

In “Basic WiFi settings” you can change the network name (SSID), assign a new password and make the network invisible to other users.
In “Advanced” you can also change the region and select the optimal WiFi channel.
“MAC Address Filter” allows you to cut off unwanted clients from the Internet using a unique device identifier.
In the “WPS” section, the function of automatically connecting to a signal or using a PIN code from other devices is activated.
Finally, in DHCP, the IP address of the modem is specified, the range of available values for distribution to other computers and the lease time for these addresses.

Control of the “wifi repeater” mode has been placed in a separate section of the menu. If you turn it on, the Huawei modem will be able to choose where to get the Internet from - from another router or from a SIM card. This is convenient if you have connected a modem to your laptop. In order not to waste mobile traffic, if you are in the area of a known Wi-Fi signal, preference will be given to it.

SD card access

And another interesting feature of the Huawei E8372h modem is its support for working with micro SD cards. It, like the SIM card, is installed inside the case. Based on it, you can create a network FTP server and open access to it for all gadgets connected to its WiFi network. This setting is located in the “Sharing” section.

By default, the “USB Only” mode is activated, that is, it is used as a regular flash drive connected to a computer. But if you move the checkbox to “FTP access”, the options described above open up.

You can give permissions only to read files or also to write. Plus select the directory to which you will open access - to the entire memory card or to a separate folder.

These are the basic modem settings, which can be found at https://192.168.8.1 or 192.168.3.1 in your Huawei account. Now you know how to enter and change them.

Firmware

The popular Huawei WS329 router model has a wide range of functionality. As standard, the device has English-language firmware version V100R001C199B01, which has IPTV support.

Additional device firmware can help eliminate some malfunctions and operational errors, as well as expand the capabilities of the device itself.

In order to change the standard firmware of the router, you need:

download the updated firmware version for the device on the manufacturer’s website;

connect the device to power and to the computer;

enter the router settings panel;

open the system settings tab “Maintenance”;

select “Software Update”;

select the downloaded software version as the firmware file;

click the “Update” button and wait for the update to complete;

check the settings, connect the provider cable.

Wi-fi router Huawei WS329 is a convenient and functional router that allows you to connect the Internet at home or in the office. This device is the most popular router for installing a high-quality and high-speed home network at home.

As a rule, installing a device of this type does not require much effort and is a fairly quick process, subject to certain rules.

If you wish, you can not waste time calling a specialist, but configure the Huawei WS329 Beeline router yourself, using the user manual and expert advice.

You can set standard device configuration settings, you can set an additional security password or change your login information, ensuring a greater degree of device security from hacking, and also install additional auxiliary accessories and antennas to increase Wi-fi coverage.

Digital television

The Huawei WS329 Wi-Fi router can be an excellent option for connecting high-speed Internet at home, as well as high-quality digital television.

To set up IPTV on your router, you need:

go to the “IPTV Service” section;
check the box next to “IPTV Enable”;
select from the list of Lan Interface ports the port to which TV4 will be connected
set the connection type to “Bridge Mode”;
set the value “4” in the “802.1P” field;
save the settings.

How to open a personal account for a Huawei modem at 192.168.100.1?

Your device (PC, laptop, smartphone) from which we will log into the web interface must be connected to a modem/terminal. You can connect either via a Wi-Fi network or using a network cable. Something like this:
You need to disable the browser on your device, enter (or copy) the address https://192.168.100.1 in the address bar and follow it (by pressing the Enter key). If the address is correct and you are connected to the terminal, an authorization window will open.
In this window you need to enter your username (Username, or Account field) and password (Password). Perhaps on your Huawei router this information is indicated on a sticker (shown in the photo above). By default, this is usually the following data: Username (Account) is root, and Password is admin. Only these are factory data; they could have been changed in the router settings. For example, a wizard when installing and configuring an optical terminal. If the modem is from the Rostelecom provider, then the login is most likely telecomadmin, and the password is admintelecom. Be sure to try it. If everything is fine, then the personal account of the Huawei modem or terminal should open. You can set up Wi-Fi (WLAN), etc.
If your login/password doesn’t work, or you don’t know it or have forgotten it, then see my instructions below.

Huawei login and password (root, admin, telecomadmin, admintelecom)

For many people, an authorization window opens at 192.168.100.1, but they don’t go into the settings because the standard login and password don’t work.

Login – root
Password – admin

But if the device was issued to you by the provider Rostelecom, Beltelecom, etc., then a different login/password is set there. Often:

Login – telecomadmin
Password – admintelecom

If this data does not suit, then I recommend calling the support of your Internet provider and asking what data to use to enter the router settings.

Or another option is to reset the settings of the Huawei router/terminal.

After resetting, you will have to configure your router again. If this was done by specialists during installation, and you are not sure that you can configure it, then I recommend first discussing the problem with the support of your Internet provider.

To do this, you need to find the Reset button on the device body (usually it is recessed into the body), press the button and hold it pressed for at least 10 seconds. The router settings will be reset to factory settings. After rebooting the router, try logging in to 192.168.100.1 and entering the factory login/password.

Startup procedure

device control panel

The components, along with the device, usually contain everything necessary to set up the operation of the device.

If this involves connecting to a computer with a patch cord (Ethernet cable), then one end should be inserted into the LAN socket of the device, and the other into the PC’s network card (of course, manufacturers also provide a Wi-Fi connection for further settings, but it is recommended log into the modem’s web-configurator via a wired connection, as this will avoid many problems when updating software and entering network characteristics).

It should be noted that you do not need a connection to the World Wide Web to enter the web interface. Next, you need to insert the cord from the power adapter into the corresponding socket in the device, often “Power” is written under it.

Apply power to the device and turn it on, if it has a button for this. If the device is not equipped with an on/off key, it will start immediately after installing the adapter into the power outlet.

The LAN LED on the front panel of the device will light up and the connection will be displayed on the PC.

After completing the wired connections, you will need to complete the following steps while sitting at your computer:

Call the context menu from the connections icon in the tray;
Click “Network and Sharing Center”;
Next, go to the “Change adapter parameters” tab;
Call the context menu from “Local Area Connection”;
Click “Properties”;
Click “Internet Protocol Version 4”;
Click “Properties”;
Set checkboxes for assigning addresses automatically;
Click “Ok” sequentially in both open windows;
Open an Internet browser;
Type “IP” of the device in the address input column (it is written on the device label, which is glued to the bottom cover. If the sticker is torn off or worn out, then you should read the accompanying documents for the equipment);
Click "Enter";
In the menu that appears, type the code and name (they are also written on the label and in the documentation);
Click “Enter”;
Ready. The desired device control panel will appear on the monitor, that is, the modem is logged in.

The design of the personal account of the device varies among developers, but basically they are Russified and provide background information.

For example, if the device is provided by the provider Rostelecom, then the menu will be made in corporate colors.

Sometimes the specified authorization parameters for device labels may not work. This means that they were previously adjusted.

In order for the name and password set by the manufacturer to take effect again, you will have to reset the settings.

To do this, find the “Reset” button on the device body and press and hold it for about ten seconds. The device will restart, and the initial parameters for entering the interface will be in effect again.

Setting up Wi-Fi: change the name of the network and set the password

Setting up the access point itself comes down to creating a network and changing the password from standard to more complex:

Expand the third section “Home Network”. Select the third tab “Wi-Fi Settings”. Check the box next to “Enable 2.4 GHz Wi-Fi.”
In the “Encryption” menu, if you want, set a new name for the Huawei router access point (if the model name does not suit you). Activate the SSID in the step below.
In security mode, select WPA2-PSK. Leave AES in the menu below.
Next, in the field, type a pre-created network password that other users will use to log into the access point. We recommend writing this combination down somewhere separately in a notepad as a reminder.
Remove the checkmarks next to the last two items. Click "Save".
Expand the "Advanced" menu. Set the transmitter power to 100% if you have a large area for Wi-Fi coverage. In network mode, set the combined value of b/g/n.
Leave the channel at “Auto” for now. If you later notice low Internet speed while working, empirically select the freest channel for your situation (install one at a time and look at the speed).
Leave the bandwidth at 20/40 MHz. Click on “Save”.

How to set up Wi-Fi on a Huawei WS329 router

In fact, setting up a Huawei WS329 Wi-Fi router is not as complicated a process as you might think. The router has a very user-friendly interface and clear configurations.

To set up a wireless Wi-Fi network on your router, you need to:

open the router settings menu;
go to the section called “WLANSetting”;
check the box next to the “Enable WLAN 2.4 GHz” configuration;
check the box next to the “Enable SSID” configuration and specify the network name in the “SSID” field;
select the security mode “WPA2-PSK”, encryption type – AES;
specify the password for the wifi network in the “WPApre-shared key” field (a sequence of at least 8 characters);
save the specified configuration changes.

The second item represents manual configuration settings. After logging in, after a few minutes the connection will be established and the “Wi-fi Settings” window will open automatically.

Indicator designation

The indications of Huawei routers are different: some models have a whole range of indicators, others have just one indicator operating in different modes

Not all router owners pay attention to studying the display, but in vain. Understanding what exactly the router is showing at the moment, you can quickly solve this or that problem

Let's look at the most typical indicator designations for routers (see picture below). The familiar power indicator is most often used to understand whether electricity is being supplied to the router. But he can also be responsible for the state of the system. The second indicator from the left shows which network the router is connected to.

The third icon from the left is responsible for Wi-Fi and (or) WPS, the fourth tells you whether devices are connected or not connected to the LAN/WAN ports, and the fifth shows the signal strength. In some models, the indicators are labeled with words, which eliminates the need to look at the instructions.